Add a field to the PMIC thermal alarm core data named
allow_software_override which is used to control whether or not
userspace may switch the mode of a PMIC thermal device to
"enabled" in order to enable software override of PMIC automatic
over temperature shutdown.
allow_software_override -
true: writing "enabled" to thermalfs mode file results in
software override of PMIC automatic over temperature
shutdown.
false: PMIC automatic over temperature shutdown is always
enabled. mode file cannot be set to "enabled".
Change-Id: I4c47fdf0c0c4704008591755296118ad7fac95ae
Signed-off-by: David Collins <collinsd@codeaurora.org>
(cherry picked from commit 8f6d8a8e7e1d149687819af7f9abbb24a8459cc0)
In order to keep card endurance, it is best not to check the need for
BKOPS every time the MMC is idle.
However, the decision when to check the card need for BKOPS according
to number of changed sectors doesn't fit all cards sizes. Therefore,
the check for BKOPS need is based on percentages of changed sectors
of the card size.
In order to assure that BKOPS will be triggered again in case it was
interrupted, the accumulated number of changed sectors is cleared only
in case BKOPS was completed without interruption.
Change-Id: I598f64b652a524a431b87d103fd5890b808f11b1
Signed-off-by: Maya Erez <merez@codeaurora.org>
(cherry picked from commit e1eae988976536834759a45cf7f62e1cb2b82838)
BKOPS operations can take long time and cause bad user experience and
failure of time critical operations as EFS sync.
In order to prevent the above failures all the levels will be handled only
in idle time BKOPS handling and will allow interrupting the BKOPS when
needed.
In case the card raised an exception with a need for BKOPS, a flag will
be set to indicate MMC to start the BKOPS activity when it becomes idle.
Fixed-CRs: 432027
Change-Id: I5f7b43569c0242f0fea83355f76f286b1ad037bc
Signed-off-by: Maya Erez <merez@codeaurora.org>
(cherry picked from commit 5f8ac3b955e44def61c2238192000ffe5f126714)
The timeout for the BKOPS polling is increased in order to allow the
card to complete the BKOPS before going to suspend.
In case we exit due to timeout we need to stop the BKOPS activity
performed by the card.
Change-Id: I39686de0c06a57242f11c8b1c9ae50b33417c088
Signed-off-by: Maya Erez <merez@codeaurora.org>
(cherry picked from commit ea1385e6d7542d4e3ad510de94ead00bece7823e)
In order to allow the card to perform BKOPS as early as possible without
causing degradation to a flow of requests, we reduce the time of the
BKOPS delayed work to 200ms.
Based on experience, 200ms will allow requests to be performed without
a delay of checking the BKOPS.
This patch also allows the host controller to set any other time if
required.
Change-Id: I1e56bfd0c9471abf4da50befe6d14fe0199129e7
Signed-off-by: Maya Erez <merez@codeaurora.org>
(cherry picked from commit 70b00220e7564b00e3b0747260fe2c2dbe62f45d)
GPU pagefault policy can be set to below options:
a) enable/disable GPU HALT on pagefaults
b) log only one pagefault per page.
GPU pagefault policy can be controled using panel file
and debugfs.
Change-Id: I0613e0d087fc45eb5e519e1c834a33f32376672f
Signed-off-by: Tarun Karra <tkarra@codeaurora.org>
If userspace requests no fault tolerance using context flag
KGSL_CONTEXT_NO_FAULT_TOLERANCE, do not attempt denial of
service detection and do not attempt fault tolerance when
a hang is detected.
Change-Id: I5de0e4ae6e8407365725c30fcb0e00a601460ebc
Signed-off-by: Tarun Karra <tkarra@codeaurora.org>
Allow userspace to control fault tolerance policy,
this allows fault tolerance policy to be controlled
using panel file.
Change-Id: I991edf6f082384bc69454058fe5df3b5f535aa4c
Signed-off-by: Tarun Karra <tkarra@codeaurora.org>
Add wcnss reset interface, this interface generates an FIQ to Riva.
Upon receiving this interrupt, Riva will execute the ERR_FATAL
routine and invoke SSR.
Conflicts:
drivers/net/wireless/wcnss/wcnss_wlan.c
include/linux/wcnss_wlan.h
Change-Id: I74c293121cb69b312ed980902a12019adb700792
Signed-off-by: Sameer Thalappil <sameert@codeaurora.org>
This reverts commit b7d35468be026b0266bcb5217b72c6fbbf8b1bc0.
Change-Id: Iba80431f304dff64ba0427870dd857fc8729be28
Signed-off-by: Deva Ramasubramanian <dramasub@codeaurora.org>
Add a pm8xxx-tm subdevice into pm8821-core. The pm8xxx-tm device
can be used to receive an interrupt when critical temperature
thresholds are reached. Since PM8821 does not have an ADC, it is
not possible to read a real time PM8821 die temperature using
this pm8xxx-tm device.
Change-Id: I3720c79a0546e8bc69044166f70dd4c313e84daa
Signed-off-by: David Collins <collinsd@codeaurora.org>
(cherry picked from commit 1604779c47df4bf003211c35e356210e689676d5)
From 81df2d594340dcb6d1a02191976be88a1ca8120c upstream.
Some composite USB devices provide multiple interfaces
with different functions, all using "vendor-specific"
for class/subclass/protocol. Another OS use interface
numbers to match the driver and interface. It seems
these devices are designed with that in mind - using
static interface numbers for the different functions.
This adds support for matching against the
bInterfaceNumber, allowing such devices to be supported
without having to resort to testing against interface
number whitelists and/or blacklists in the probe.
Change-Id: I0f991e507d041bbe12aa87403b9c2e1f0de274c2
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
The ADSP heap is intended to be used for post processing
on the dsp. Add the definiton of the heap to allow clients
to have dedicated access
Change-Id: I80040b0cf3311df90970c156aa3329f07fc9a990
CRs-Fixed: 438281
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Previously the WFD driver was reponsible for signalling the
online/offline events to userspace listeners. This led to redundant
notifications due to the manner in which the WFD driver is used. The
signalling is better purposed when done from MDP driver.
Change-Id: I2248de84d57504c2fa9f26e1bfdf0e0d4a02257a
Signed-off-by: Deva Ramasubramanian <dramasub@codeaurora.org>
Updated the last message SSID and the buildtime masks to reflect
the additions on the Modem.
Change-Id: I9a62942f5daf14268b0f61f81cbb53b76901d012
CRs-Fixed: 448735
Signed-off-by: Ravi Aravamudhan <aravamud@codeaurora.org>
Added a check for separate metadata buffers based on
the board specific platform data.
Change-Id: I24d51329d93215da75d115ccfa8fc1f3fe260b7f
Signed-off-by: Deepak Verma <dverma@codeaurora.org>
Conflicts:
drivers/video/msm/vidc/1080p/resource_tracker/vcd_res_tracker.c
Signed-off-by: Deepak Verma <dverma@codeaurora.org>
Currently we have 4 mins timeout for the blocking BKOPs to complete
but we have seen instances where card is surprisingly taking even
longer time to complete background operations.
If card doesn't complete the BKOPs within specified timeout, we
will send the HPI command to interrupt the ongoing BKOPs.
Change-Id: I5df81bdfd9b19bee30a394ee0ff4390b292691d0
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
(cherry picked from commit 1b22222ec61924de9b8ac51f08de113548946eb5)
Update type from u8 to uint8_t for trepn daemon usage
from userspace. Also expose the psoc structures for
trepn's use.
Change-Id: I840a480432493303b105396d522ebdcb1cf9079a
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
commit 8e6edcb (usb: ehci: Avoid phy lockup due to SOFs during port
reset) implements a workaround for PHY lockup issue during port reset.
The workaround relies on a hardware debug feature which allows driving
strobe and data lines to reset using ULPI interface. This is not
working some times for unknown reason.
This patch implements a new reset sequence to workaround the PHY lockup
issue. The controller drive reset signaling for ~50 msec when reset bit
is set in PORTSC register. The controller automatically clears this bit
after finishing the reset signaling. The software can also finish the
reset signaling any time by clearing the reset bit.
According to USB2 spec, Host controller should drive reset signaling for
50 msec for root hub ports. But HSIC spec allows shorter reset signaling
time (20 msec). Clear the reset bit in PORTSC register after 20 msec and
start controller immediately to send SOF. Use controller internal timers
to achieve this. If reset bit is not cleared in time, perform the sequence
in a loop with interrupts disabled.
CRs-Fixed: 445659
Change-Id: I6b251ced8d47b9ece4a06e58baf15c69a8bb340f
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Reading the current value of TSIF clock reference counter
is required by some application.
Change-Id: I5ca2a280f864fbb9c4a69518ce9672538f9c8489
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
MSM9625 implements ETM based on ETM version 3.5.
As such the 9625 ETM registers need some additonal configuration
for ETM to be functional. They also have some extra registers which
need to be configured properly while some registers currently being
configured by the driver are absent on 9625. Additonally, the ETMv3.5
can be configured to support data tracing, support for which is
not present in the existing ETM driver.
Change-Id: Ic3e61d0d1abf371653a398a28111b308747a7b6f
Signed-off-by: Pushkar Joshi <pushkarj@codeaurora.org>
Qview entity id will be used to support transporting qview data
and will also be used by the host tool for decoding.
Change-Id: Idbe017e34676921c33be5d46f57697ce7322af90
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Add support to transport data sent using userspace library over
STM. Data stream will contain the entity id, protocol id and
options.
Change-Id: I5bd1810338fd13373bbad7de559765002c43c500
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Remove license info from coresight-stm.h header file as it
is exported to userspace.
Change-Id: I49968e160fd2eb2e1499bb4c07b56676e9b280c6
Signed-off-by: David Ng <dave@codeaurora.org>
Export coresight-stm header for userspace STM logging
definitions.
Change-Id: I75923ea8beea36269995e311c3fbb2667beac3cc
Signed-off-by: David Ng <dave@codeaurora.org>
Move debug arch defines to jtag.c since they aren't used anywhere else.
Also rename ARM_DEBUG_ARCH_V7_1 to ARM_DEBUG_ARCH_V7p1 to avoid clashes
with similar define in hw_breakpoint.h that is enabled when hardware
breakpoints are enabled.
Change-Id: I5f4b24b7aec50413f97a5b1854e6fadf2e4ab514
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Since we can use ftrace event to also log printk to STM, remove
direct logging of printk to STM.
Change-Id: I903e2584b40565513342864827455f0a6cbf2260
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Support for etr to usb trace output using QDSS BAM to USB BAM
transfers.
Change-Id: Ibb6f8d0cf1d9799668cb22ccaa13966139c8dea5
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Change CONFIG_MSM_QDSS to granular CORESIGHT configs covering
various CoreSight drivers. This better represents the CoreSight
device topology and allows more flexibility in choosing the
drivers required for a particular platform or chip.
Conflicts:
arch/arm/configs/msm8960-perf_defconfig
arch/arm/configs/msm8960_defconfig
arch/arm/configs/msm8974-perf_defconfig
arch/arm/configs/msm8974_defconfig
arch/arm/configs/msm9625_defconfig
arch/arm/mach-msm/Kconfig
drivers/coresight/Kconfig
drivers/coresight/Makefile
drivers/coresight/coresight-etm.c
drivers/coresight/coresight-priv.h
Change-Id: I5ae44442c24c88673f2045ad24dc89e4d86d23cb
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
In cherry-picking patches from tip, the LTC charger driver and pm8921
BMS driver header were updated without updating the copyright
marking from "Code Aurora Forum" to "The Linux Foundation".
Fix this by updating the copyrights now
Change-Id: I3a24feaa6af5acbdca4fc6499398205a1c93dcfe
Signed-off-by: Xiaozhe Shi <xiaozhes@codeaurora.org>
Extradata is appended at the end of each output buffer
in non secure video use case but in secure video playback,
the client/CPU don't have access to the output buffer
to parse the extradata. This change allows the client/CPU
to parse the extradata by allocating separate buffers for
video hardware to store extradata.
Change-Id: I12927ea3d142b9cecd6fb1ae1086c5624d0e08d6
Signed-off-by: Deepak Verma <dverma@codeaurora.org>
This change adds support for demuxing of encrypted streams which current
software demux implementation does not support.
User-space API is extended to allow setting of key ladder information
needed in order to perform decryption.
If secure demux application is available, demuxing does not take place in
the dvb demux sw filter anymore but instead is performed in the new secure
demux, regardless of whether the stream is encrypted or not.
Otherwise, the dvb demux sw filter will be used as before and demuxing of
encrypted streams will not be available.
Change-Id: If75a7b03d1f13d3b012250b87c25eaf6d6cbc399
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Report counters for transport error indicator, continuity-counter
errors and total number of TS packet constructing a PES in the
PES events so that applications can decide whether to decode
or drop the packet based on the errors information.
Change-Id: I8680163783a12c4f2518cd83fa0b3c7dfa882c34
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
The NL80211_CMD_TDLS_OPER command was previously used only for userspace
request for the kernel code to perform TDLS operations. However, there
are also cases where the driver may need to request operations from
userspace, e.g., when using security on the AP path. Add a new cfg80211
function for generating a TDLS operation event for drivers to request a
new link to be set up (NL80211_TDLS_SETUP) or an existing link to be
torn down (NL80211_TDLS_TEARDOWN). Drivers can optionally use these
events, e.g., based on noticing data traffic being sent to a peer
station that is seen with good signal strength.
Change-Id: I778f5136fc4518bedcaed14a5412de4be6c85cf3
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Ng Chilam <chilamng@qca.qualcomm.com>
[Madan Mohan Koyyalamudi <mkoyya@codeaurora.org>: move changes from
include/uapi/linux/nl80211.h to include/linux/nl80211.h, remove trace.h,
remove trace_cfg80211_tdls_oper_request() in nl80211.c ]
Signed-off-by: Madan Mohan Koyyalamudi <mkoyya@codeaurora.org>
All userspace consumers should now be using IOCTL_KGSL_GPUMEM_ALLOC,
so we can safely remove this kludgy and deprecated code. The structs
and #defines are left in the header to avoid breaking userspace and
to serve as a reminder of the way we were, but any use of
IOCTL_KGSL_SHAREMEM_FROM_VMALLOC will return -ENOTTY.
Change-Id: Ic0dedbad1460acfe28116ee2dbd75faa52b76857
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Update the Compander register settings to remain the default
settings after the system bootup and optimize compander
configuration sequence.
Change-Id: Ib475f3bb84414546b4ead1d3f013dc173317e1b3
Signed-off-by: Kuirong Wang <kuirongw@codeaurora.org>
Revert the following customer changes in order to clean up this
branch.
This reverts commit 33ddf5a9eaa031c00b00846458f2ba534e6807b8.
This reverts commit f17df2402b795faf2c03de6d8a5b12378674f3be.
This reverts commit 0a488464c03806e1f775c35d7b2c83650eaab4ef.
This reverts commit 23d2a7cd02b081e1cf2578c02b7ecd3a65319d4e.
This reverts commit 90e32fa7cb701d922825e40b82b566e4af843ea2.
This reverts commit 7346d0fbd3c338d55330766e0f1867f19b364fed.
This reverts commit eb59bf66db9f2ca6e79552f4f72aa56f8c6abd27.
This reverts commit 9c56de000bb2390191fa2ddaea738e6d3e8f5d4f.
This reverts commit 7a72ca62c3f64c7b914edd8d9dbb75933b3c845e.
This reverts commit 76048dac5085eca4459ee5ea5dd4876a1f518cfa.
This reverts commit bfafe7ec7cdeef5b44b32f9aa6ee03beba2020e0.
This reverts commit e346f7a7b8ead1bbb106f4eb1e766c49407bffde.
This reverts commit 1265899c012a463cb0521ed73f2abe057692a9db
This reverts commit 1ff608a341b87defa586ca4a24d0bd89abfdfbb3
This reverts commit 5f030effc8c1af159ad13e77d4c169f037d6c9e4.
This reverts commit 19c87ddde66fd6aad61a60e466a75af235fca7f9.
This reverts commit 905eac978c30c96c5d12a81c1f6968d8c57a645f.
This reverts commit 1bd7c8643cdd8fdc7cf649ec465cc454315a6753.
This reverts commit 69f1730e0d249bad3b4f0fc0f94d917c16c3df19.
This reverts commit 2073afb7ee8b3f80f1f3184bd7ac99ead581adee
This reverts commit 8126554cf049d13f4dd2d815d86ea289efdc6f3a.
This reverts commit 45ccbb53cfc227fd3811e71b0bd813432c96ee9e
This reverts commit 325995993eb806285a35381e803ed5432fe5a93a.
This reverts commit 84cf5a3959bcf412c4b48f8a29b8255c18602d1b.
This reverts commit 839d5a50c761787ded6b8558fa37696be81196fe.
This reverts commit d4b1fb57463d04aeca5ae9bfd2181faa016f97c2.
This reverts commit 2ab04b0deb912a5a52899a50ced73e36974a6a00.
This reverts commit 3a3de0ee621625c8767e0d3c7106c52fcf834499.
This reverts commit f278add027723a90b11c9a97f6d1b09c1aaec795.
This reverts commit 1a749b700752efcc8d832f7b83554df2771dce53.
Change-Id: I21863586360b6bc57dd6d631c34725bea963cffa
Signed-off-by: Xiaozhe Shi <xiaozhes@codeaurora.org>
diag on the A-Family mainline is out of date. Create a commit
to bring diag up to date.
Change-Id: Ie24780b4b83a3cb378326357d70785a590167447
Signed-off-by: Dixon Peterson <dixonp@codeaurora.org>
Battery charging specification allows data contact detection (DCD)
timeout to be any value between 300 and 900 msec. As DCD is reliably
working, increase the timeout for detecting slow cable insertion cases.
DCD would fail with ACA-dock and ACA-A + HS/FS device. Use 750 msec
as timeout. The 150 msec (900 - 750) safe guard time compensates the
time taken from session valid to DCD enable. Decrese the DCD polling
period from 100 msec to 50 msec to exit DCD state quickly.
The 150 msec safe guard time compensates the time taken from session valid
to starting charger detection procedure.
CRs-Fixed: 437484
(cherry picked from commit ebb4a2d613128a2db288402bc834622a36e71956)
Conflicts:
drivers/usb/otg/msm_otg.c
Change-Id: I0e014d2ae0f9e00eaba179af2244924cf4561c90
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Add definition for struct to be used in post processing calibration API.
Needed by OEM calibration tool to provide better support of post processing
features.
Change-Id: I40760a85bb58730bfe64469ecf3e2ab3b6e7609e
Signed-off-by: Carl Vanderlip <carlv@codeaurora.org>
(cherry picked from commit e8ed5ec0bd9fd5b298464b7f08b5807afa3291a8)
-Non tunnel playback is use case where compressed
data is sent to driver(for decoding) and
caller expects PCM data back from the driver.
-Add non-tunnel driver for amr-wb+.
-Add support for amr-wb+ in asm driver
Change-Id: I266e70dff0466a20b0435da840a31a8a1774cf35
Signed-off-by: Ajit Khare <ajitk@codeaurora.org>
Previously, a parameter was added to secure heaps to only
allow secure allocations. Some clients still require
non-secure contiguous allocations even though the SMMU is
supported. Add support for those clients to force contiguous
allocations to go through.
Change-Id: I0d18d8a9ed3ab267b55c84c4ad160f8cec2c2b32
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
This reverts commit 355c0ffe69b90b08ec4621bdb0964b42c6bb7eed.
Reverting it, as this is being handled in Display HAL now.
Change-Id: I2d807a17193c8d579bb23378e59817374d3f4ad7
Signed-off-by: Sushil Chauhan <sushilchauhan@codeaurora.org>
Remove unused fence input in mdp_display_commit
structure
Use different timeline name for different fb
Change-Id: I4edd335b36dce057ff3e54302af6088a9cc470ec
Signed-off-by: Ken Zhang <kenz@codeaurora.org>
Although not in internal reference designs, customers
may need to use pmic based vibrator instead of isa1200.
CRs-fixed: 416276
Change-Id: I190840eee4862ac82c5120501748b795e6d0c760
Signed-off-by: Amy Maloche <amaloche@codeaurora.org>
Signed-off-by: Neha Pandey <nehap@codeaurora.org>
